Integrals add up quantities that change from point to point. A rod whose density varies, a disk that is denser near the center, a spring that pushes back harder the more it is stretched, and water that must be lifted different distances from different depths: in each case we cut the object or the motion into small pieces, approximate each piece by a constant, add, and take the limit. The result is a definite integral.
01 · Mass of a thin rod
A thin rod lies along the x-axis from x = a to x = b. If its density (mass per unit length) is a constant ρ, its mass is ρ(b − a). If the density ρ(x) changes from point to point, cut [a, b] into n pieces; the piece [xᵢ₋₁, xᵢ] has mass mᵢ ≈ ρ(xᵢ*)Δx. Adding gives a Riemann sum, and in the limit
m = limn→∞ Σ ρ(xᵢ*)Δx = ∫ab ρ(x) dx.
Example: a rod on [π/2, π] with density ρ(x) = sin x has mass ∫π/2π sin x dx = [−cos x]π/2π = 1 − 0 = 1.
02 · Mass of a disk with radial density
A thin disk of radius r is centered at the origin, and its density depends only on the distance x from the center: ρ(x) (mass per unit area). Cut [0, r] into pieces; each piece sweeps out a thin ring with inner radius xᵢ₋₁ and outer radius xᵢ, of area π(xᵢ² − xᵢ₋₁²) = π(xᵢ + xᵢ₋₁)Δx ≈ 2πxᵢ*Δx. Its mass is about 2πxᵢ*ρ(xᵢ*)Δx, so
m = ∫0r 2πx ρ(x) dx.
Example: ρ(x) = 3x + 2 and r = 2: m = 2π∫02 (3x² + 2x) dx = 2π[x³ + x²]02 = 24π.
03 · Work done by a variable force
A constant force F moving an object a distance d does work W = Fd. If the force F(x) varies as the object moves along the x-axis from a to b, then
W = ∫ab F(x) dx.
| system | length | force | work |
|---|---|---|---|
| metric | meters (m) | newtons (N) | joules (J) |
| English | feet (ft) | pounds (lb) | foot-pounds (ft-lb) |
Hooke's law: the force needed to stretch or compress a spring x units from its natural (equilibrium) length is F(x) = kx, where k > 0 is the spring constant.
Example: a force of 30 N stretches a spring 5 cm = 0.05 m, so 30 = k(0.05) and k = 600 N/m. To stretch it an additional 20 cm (from 0.05 m to 0.25 m): W = ∫0.050.25 600x dx = 300[x²]0.050.25 = 300(0.0625 − 0.0025) = 18 J.
04 · Work done in pumping
- Sketch the tank and choose a coordinate: here x is the depth below the top.
- Find the volume of a representative thin layer of liquid at depth xᵢ*.
- Multiply by the weight density of the liquid to get the force needed to lift it (water: 62.4 lb/ft³).
- Find the distance the layer must be lifted.
- Multiply force by distance to get the work for that layer.
- Add the work for all layers: a Riemann sum.
- Take the limit to get an integral, and evaluate it.
Example: a tank is an inverted cone of height 12 ft and top radius 4 ft, full of water. Water is pumped over the top edge until 4 ft of water remain. A layer at depth x has radius r with r/(12 − x) = 4/12 (similar triangles), so r = 4 − x/3; its volume is about π(4 − x/3)²Δx and its weight 62.4π(4 − x/3)²Δx, and it is lifted x ft. The layers to remove run from x = 0 to x = 8, so
W = ∫08 62.4π x(4 − x/3)² dx = 62.4π · 512/3 = 10,649.6π ≈ 33,457 ft-lb.
Guided problems · Physical Applications
Original problems on mass, density, and work. Open a hint if you need one, check your answers, then try another set.
Check your understanding · Physical Applications
Answer each question on paper first, then open the answer to check yourself.
A rod on [π/2, π] has density ρ(x) = sin x. What is its mass?
Show answer
m = ∫π/2π sin x dx = [−cos x]π/2π = 1.
A disk of radius 2 has radial density ρ(x) = 3x + 2. What is its mass?
Show answer
m = ∫02 2πx(3x + 2) dx = 2π[x³ + x²]02 = 24π.
A force of 30 N stretches a spring 5 cm. How much work stretches it an additional 20 cm?
Show answer
k = 30/0.05 = 600 N/m, and W = ∫0.050.25 600x dx = 300(0.25² − 0.05²) = 18 J.
