University of Texas Rio Grande Valley

Current teaching · Edinburg, Texas · Fall 2026
MATH 1314 · WEEK 2 · SECTION 3.3

Rates of Change and Behavior of Graphs

How fast is a function changing, and where is it rising or falling?

A function can tell us more than single values. Comparing two outputs tells us how fast the function changes, and tracing a graph from left to right tells us where it rises, falls, or stays flat.

Learning objectives Find the average rate of change of a function from a formula, a table, and a graph; use a graph to determine where a function is increasing, decreasing, or constant.

01 · Average rate of change from a formula

Definition · Average rate of change

Over an interval [x₁, x₂], the average rate of change divides the change in outputs by the change in inputs:

Average rate of change = ΔyΔx = f(x₂) − f(x₁)x₂ − x₁

Geometrically, it is the slope of the secant line through the two points (x₁, f(x₁)) and (x₂, f(x₂)).

INTERACTIVE · SECANT LINE LAB

Choose a function and move the two inputs. The orange legs show Δx and Δy, and the blue secant line has slope Δy/Δx. Follow the four steps below the graph.

Try this: Pick the line q(x) = 6 − 2x and move both inputs anywhere. Why does the average rate of change never change? Then pick f(x) = 3x² − 5 and find two different intervals that give the same rate.

02 · Average rate of change from a table

When a function is given as a table, read y₁ and y₂ directly from the table. Choose two inputs; the table and the plotted points highlight what you are using.

INTERACTIVE · TABLE TO SLOPE

03 · Average rate of change from a graph

From a graph, find the two points above x₁ and x₂, read their y-coordinates, and divide. The graph below is a parabola; choose an interval to read.

INTERACTIVE · READ, THEN DIVIDE

04 · Increasing, decreasing, or constant

Definitions

On an interval (a, b), a function is increasing if its outputs get larger as the inputs get larger, decreasing if its outputs get smaller as the inputs get larger, and constant if its outputs stay the same.

Always read the graph from left to right, and write the intervals using the x-values with parentheses.

INTERACTIVE · WALK THE GRAPH

Slide the walker from left to right. The walker reports whether the graph is going up, down, or staying flat at that spot. Write your intervals first, then turn on Show the intervals to check.

PRACTICE

Guided problems · Rates of Change and Behavior

Original problems on average rate of change and graph behavior. Open a hint if you need one, check your answers, then try another set.

Choose an answer for each problem.
WRAP-UP

Check your understanding · Rates of Change and Behavior

Answer each question on paper first, then open the answer to check yourself.

  1. What does the average rate of change of f on [x₁, x₂] measure, and how do you compute it?

    Show answer

    It measures how much the output changes, on average, per unit change in the input. Compute (f(x₂) − f(x₁)) / (x₂ − x₁); it is the slope of the secant line through the two points.

  2. Find the average rate of change of f(x) = x² − 3x on the interval [−1, 2].

    Show answer

    f(−1) = 1 + 3 = 4 and f(2) = 4 − 6 = −2. The rate is (−2 − 4)/(2 − (−1)) = −6/3 = −2.

  3. The table shows x = 0, 2, 5 with outputs 4, 10, 1. What is the average rate of change from x = 0 to x = 5?

    Show answer

    (1 − 4)/(5 − 0) = −3/5. On average the output drops 3/5 of a unit per unit of x.

  4. How do you find the intervals where a function is increasing from its graph?

    Show answer

    Trace the graph from left to right. Where it rises, record the x-interval with parentheses, for example (−∞, −2) ∪ (2, ∞).

  5. Can the average rate of change be 0 on an interval even if the function is not constant there?

    Show answer

    Yes. For g(x) = (x − 1)², g(0) = g(2) = 1, so the rate on [0, 2] is 0, but the graph goes down and then up in between.