University of Texas Rio Grande Valley

Current teaching · Edinburg, Texas · Fall 2026
MATH 2412 PRECALCULUS · SECTION 805 · WEEK 1 · 5.1

Angles

How do we measure a turn, and what happens after one full rotation?

Trigonometry starts with a turn. An angle is made by rotating a ray about its endpoint, and the amount of rotation can be measured in degrees or in radians. In this section we draw angles in standard position, convert between the two units, find coterminal and reference angles, and use radians to measure arcs, sectors, and circular motion.

Learning objectives Draw angles in standard position; convert between degrees and radians; find coterminal angles; find the length of a circular arc and the area of a sector; use linear and angular speed to describe motion on a circular path.

01 · Angles in standard position

Definitions · Angle and standard position

An angle is the union of two rays with a common endpoint called the vertex. The ray where the rotation starts is the initial side, and the ray where it stops is the terminal side.

An angle is in standard position when its vertex is at the origin and its initial side lies along the positive x-axis. A counterclockwise rotation gives a positive angle, and a clockwise rotation gives a negative angle. A quadrantal angle has its terminal side on an axis: 0°, 90°, 180°, 270°, 360°, ….

INTERACTIVE · DRAW AN ANGLE IN STANDARD POSITION

Pick a preset angle, move the slider, or drag on the graph. Watch the direction of the rotation arrow and the quadrant where the terminal side stops.

Try this: Draw 150° and then −150°. Both terminal sides are to the left of the y-axis, but they are not in the same quadrant. Predict each quadrant before you check.

02 · Degrees and radians

Two units for one rotation

One degree (1°) is 1/360 of a full rotation, so a full circle is 360°. One radian is the central angle whose arc has the same length as the radius. A full circle is 2π radians, so 180° = π radians and 1 radian = 180°/π ≈ 57.3°.

  • Degrees → radians: multiply by π/180°.
  • Radians → degrees: multiply by 180°/π.
INTERACTIVE · WHAT IS ONE RADIAN?

Lay copies of the radius along the circle. Each radius-length of arc adds one radian to the central angle.

INTERACTIVE · CONVERTER WITH STEPS

Type an angle such as 45, −55, or 530 in degrees, or 5π/6, −3π/2, or 2 in radians. Type π as π or pi.

03 · Coterminal angles and reference angles

Definitions · Coterminal and reference angles

Two angles in standard position are coterminal if they have the same terminal side, for example 30° and 390°. To find the coterminal angle between 0° and 360° (or 0 and 2π), subtract 360° (2π) from an angle that is too large, or add 360° (2π) to a negative angle, as many times as needed.

The reference angle θ′ of an angle θ is the acute angle formed by the terminal side and the x-axis. For θ between 0° and 360°:

  • Quadrant I: θ′ = θ
  • Quadrant II or III: θ′ = |180° − θ| (or |π − θ|)
  • Quadrant IV: θ′ = 360° − θ (or 2π − θ)
  • Other angles: find the coterminal angle first, then its reference angle.
INTERACTIVE · COTERMINAL ANGLE, THEN REFERENCE ANGLE

Choose a preset angle, or type your own in degrees or radians.

04 · Arc length and the area of a sector

Formulas · θ must be in radians

On a circle of radius r, a central angle θ measured in radians cuts off an arc and a sector with

arc length s = rθ and area A = ½ r²θ.

If θ is given in degrees, convert it to radians first.

INTERACTIVE · ARC AND SECTOR CALCULATOR

The default values are a radius of 10 cm and a central angle of 60°.

FIND THE MISTAKE

05 · Linear and angular speed

Definitions · Motion on a circular path of radius r
  • Linear speed v is distance traveled (arc length s) per unit time: v = s/t.
  • Angular speed ω is the angle turned per unit time: ω = θ/t.
  • When ω is in radians per unit time, v = rω.
  • One rotation is 2π radians, so N rotations per unit time give ω = 2πN radians per unit time.
INTERACTIVE · BICYCLE WHEEL

A tachometer measures how fast the wheel turns (revolutions per minute). Change the diameter and the RPM and follow the steps from angular speed to road speed.

PRACTICE

Guided problems · Angles

Original problems on degrees and radians, coterminal and reference angles, arcs, sectors, and angular speed. Open a hint if you need one, check your answers, then try another set.

Choose an answer for each problem.
WRAP-UP

Check your understanding · Angles

Answer each question on paper first, then open the answer to check yourself.

  1. Convert 40° and −55° to radians, and convert 11π/6 to degrees.

    Show answer

    40° = 40π/180 = 2π/9; −55° = −55π/180 = −11π/36; 11π/6 × 180°/π = 330°.

  2. Find the angle in [0°, 360°) coterminal with 861°, and the angle in [0, 2π) coterminal with −12π/7.

    Show answer

    861° − 360° − 360° = 141°. −12π/7 + 2π = −12π/7 + 14π/7 = 2π/7.

  3. Find the arc length and the sector area for a circle of radius 7 in and a central angle of 83°. Round to two decimal places.

    Show answer

    θ = 83π/180 ≈ 1.4486 rad. s = rθ ≈ 7(1.4486) ≈ 10.14 in. A = ½r²θ ≈ ½(49)(1.4486) ≈ 35.49 in².